KTM 4-Stroke Countershaft Dome Washer – DT-DW

dome_washer

Product Description

KTM 4-stroke counter-shaft dome washer.

Fits all KTM 4-strokes (00-2014) up to 530cc. Also fits most Husaberg and Beta 4-strokes.

Our testing has determined that the OEM dome washer is made of mildly heat treated material. When that component is installed under a tightened counter-shaft bolt, it is taken well beyond it’s “yield” or “elastic” limit and permanently deforms. In that condition in cannot maintain the thrust pressure necessary to keep the sprocket tight to the splined shaft. That leads to two different  failures. First, the O-ring is allowed enough clearance that is begins seeping. Secondly, the backlash between the splined shaft and sprocket is allowed to more freely pound in each direction, as the torque of power verses compression reverses itself.

Dirt Tricks has developed a tool steel, heat-treated dome washer that develops two to three times the pre-load force without reaching its elastic limit and without over-stressing the mating components. This solves O-ring leakage as well as extending the life of both the counter-shaft and sprocket splines. A counter-shaft replacement alone, with labor costs in excess of $700.

If you plan to keep your KTM four-stroke for many seasons this product is well worth the investment. Note: There are 2 different KTM front sprockets available on the market. One is intended for the 620-690′s but will it appear to fit on a regular 125-530cc KTM. It is a much wider sprocket at 11.4mm where a standard sprocket should be 8.8mm. If you attempt to run this thicker sprocket on your KTM, catastrophic failure of the washer will result. To ensure you have the correct sprocket, the countershaft should stick though the face of the sprocket. If it does not, -if the countershaft comes several mm’s from sticking though the sprocket – you have the wrong sprocket! Our part number for the wider sprocket is KTM2, and it only should be used on KTM 620-690 and the KTM 450 Rally Bike.

 

KTM Countershaft Dome Washer

KTM Front Sprockets and Oil Leakage: There seems to be a number of myths floating that associate certain front sprockets with oil leakage on KTM four-strokes. The sectioned model below should clarify this. Oil is sealed at two points on the countershaft: Everything to the right of the lip seal (cream color) is submersed in oil. First at the O-ring. This is a static or non-sliding seal that rotates with the countershaft/sprocket. As can be seen, the dome washer on the outside of the sprocket loads all of the elements, beginning with the screw, then the dome washer, the seal spacer bushing, an O-ring, and finally the inner race of the countershaft bearing. If the dome washer becomes distorted and flattened, it allow this stack of parts to develop clearance between them including the O-ring seal faces. If you are leaking oil around your sprocket, first check to see if the dome washer can be spun with some channel locks. If it can be spun, buy a new dome washer. Yours is flattened. Yes, a slightly thicker sprocket will make up for a worn dome washer, but the sprocket is not the cause. It would be like milling a cylinder head to make up for bad compression rings. Second is the countershaft lip seal: This is a sliding seal – the seal being stationery and the shaft/bushing spinning. KTM has a very good design here in that they have used a hardened steel bushing to minimize wear from the seal. Do not begin changing this seal unless you have first ruled out the O-ring issue described above. The most common cause of these leaks is a flattened dome washer allowing clearance around the O-ring. It only take .010″ of clearance (.25mm) to allow seepage.

 

KTM-CounterShaft-Section

 

The Dirt Tricks Solution:

 

Our testing has determined that the OEM dome washer is made of mildly heat treated material. When that component is installed under a tightened countershaft bolt, it is taken well beyond it’s “yield” or “elastic” limit and permanently deforms. In that condition in cannot maintain the thrust pressure necessary to keep the sprocket tight to the splined shaft. That leads to two different failures. First, as described above, the O-ring is allowed enough clearance that is begins seeping. Secondly, the backlash between the splined shaft and sprocket is allowed to more freely pound in each direction, as the torque of power verses compression reverses itself. Dirt Tricks has developed a tool steel, heat-treated dome washer that develops two to three times the preload force without reaching it’s elastic limit and without overstressing the mating components. This solves O-ring leakage as well as extending the life of both the countershaft and sprocket splines. A countershaft replacement alone, with labor costs in excess of $700. If you plan to keep your KTM four-stroke for many seasons this product is well worth the $25 investment. (Item now available!)

Part # KT-DW

DSC03680

How strong is a Dirt Tricks Dome Washer? This test was repeated 12 times, when we measured the washer, it only lost .008 of overall thickness.

 

Description
DOME WASHER - KTM
Product Options
#OptionPriceSale Price
1KTM counter shaft dome washer - DT-DW$25.00
Order DOME WASHER - KTM KTM counter shaft dome washer - DT-DW @ $25.00